22 years of industry experience in mechanical parts manufacturing


Basic knowledge about sprocket processing of sprocket

by:HENRY PARTS     2020-09-30
Tell me something about the sprocket machining the basic knowledge of the chain, sprocket & ndash; — The structure of the sprocket design: 1. The sprocket tooth profile sprocket tooth profile must ensure that the chain energy saving mesh smooth entry and exit freely, minimize the impact of the meshing of link and contact stress, and is easy to be processed. Commonly used sprocket tooth face, it consists of three sections of circular arc aa, ab, CDS and a straight line BC, referred to as 'three - circular arc Linear tooth shape. Sprocket tooth profile using a standard cutting tool processing, work in don't have to draw end tooth shape on the graph, only need to indicate on the diagram & quot; Tooth profile according to the 3 rgb1244 - 85 regulations manufacturing & quot; Can, but should draw the axis of the sprocket tooth surface, as shown in figure 2, the size refer to the design manual. Had mentioned parameter calculation in front, do not repeat narrative! 2. Chain structure of 4 kinds of common chain structure. Small diameter chain made of integral of medium diameter, the chain more radial plate, for ease of handling, loading and weight loss, on the radial plate hole, large diameter sprocket can be made into modular, the ring gear and the wheel core can use different materials to make! The C45, for example, the material such as stainless steel. 3. Chain sprocket materials should guarantee the tooth has enough strength and abrasion resistance, so the sprocket tooth surface is generally after heat treatment, to a certain hardness. Second, the sprocket processing & ndash; — Sprocket maintenance: 1, appropriate to the looseness of the chain pulley, too tight will increase power consumption, bearing wear and tear; Too loose chain easy to beat and take off the chain. Tightness of sprocket: filed or under pressure from the central part of the chain wheel, chain wheel center distance of about two 2% to 3%. 2, chain wheel mounted on a shaft should not swing and skew. Two sprockets face in the same transmission components should be located on the same plane, the sprocket center distance in 0. 5 meters, can be deviation of 1 mm; Sprocket center distance in 0. More than 5 meters, can be deviation of 2 mm. But you can't have friction sprocket profile phenomenon, if the two rounds of offset too prone to take off the chain and accelerated wear and tear. When replacing sprocket must pay attention to check and adjust the offset. 3, after the sprocket wheel wear serious, should replace new sprocket and chain wheel at the same time, to ensure good mesh. Can not only replace new sprocket or sprocket alone. Otherwise it will cause bad meshing speed new sprocket or new sprocket wheel wear. Sprocket tooth surface wear to a certain degree to flip timely after using ( Adjustable surface using sprocket) To extend the use time. 4, new chain wheel is too long, or elongation after use, it is difficult to adjust, can see things down link, but must be even. Through the link from the chain wheel on the back of the lock plate inserted in the outside, lock piece of opening should be toward the rotation in the opposite direction. 5, sprocket in the work should be timely filling lubricating oil. Lubricating oil must be into the roller and the inner sleeve fit clearance, to improve working conditions, reduce wear and tear. 6, old cannot be used mixed with part of the new chain sprocket, otherwise easy to impact in the transmission, snap sprocket. 7, machine long stored, chain wheel should be removed with kerosene or diesel clean, then coated with oil or butter in a dry place. Given yuan is a commitment to the development of coating equipment and related equipment, manufacturing equipment and accessories manufacturing of high-tech enterprises, mainly engaged in coating production of spare parts, precision parts processing, chain wheel processing, batch parts processing, tel: 0086 - 574 - 55224980!
NINGBO HENRY PARTS INC. is experienced in producing mechanical parts manufacturer SERVICE products featuring topnotch quality with ODM services available. Welcome to visit our site at HENRY PARTS.
To build customers value by delivering high-quality products, services and solutions in innovative and cost effective ways. NINGBO HENRY PARTS INC. will realize this mission by setting the highest standards in service, reliability, safety and cost containment in our industry.
NINGBO HENRY PARTS INC. will need to find one that fits our needs and budgets, and still turns out a quality product.
Our company specializes in selling SERVICE as well as providing relevant services.
Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...